diff --git a/arch/powerpc/cpu/mpc83xx/Kconfig b/arch/powerpc/cpu/mpc83xx/Kconfig
index 3fb901f..3ea62ca 100644
--- a/arch/powerpc/cpu/mpc83xx/Kconfig
+++ b/arch/powerpc/cpu/mpc83xx/Kconfig
@@ -67,6 +67,9 @@
 config TARGET_HRCON
 	bool "Support hrcon"
 
+config TARGET_STRIDER
+	bool "Support strider"
+
 endchoice
 
 source "board/esd/vme8349/Kconfig"
diff --git a/board/gdsys/common/Makefile b/board/gdsys/common/Makefile
index 95e41de..ba48e8b 100644
--- a/board/gdsys/common/Makefile
+++ b/board/gdsys/common/Makefile
@@ -9,7 +9,9 @@
 obj-$(CONFIG_CMD_IOLOOP) += cmd_ioloop.o
 obj-$(CONFIG_IO) += miiphybb.o
 obj-$(CONFIG_IO64) += miiphybb.o
-obj-$(CONFIG_IOCON) += osd.o mclink.o dp501.o phy.o
+obj-$(CONFIG_IOCON) += osd.o mclink.o dp501.o phy.o ch7301.o
 obj-$(CONFIG_DLVISION_10G) += osd.o dp501.o
 obj-$(CONFIG_CONTROLCENTERD) += dp501.o
 obj-$(CONFIG_HRCON) += osd.o mclink.o dp501.o phy.o
+obj-$(CONFIG_STRIDER) += mclink.o dp501.o phy.o ioep-fpga.o adv7611.o ch7301.o
+obj-$(CONFIG_STRIDER_CON) += osd.o
diff --git a/board/gdsys/common/adv7611.c b/board/gdsys/common/adv7611.c
new file mode 100644
index 0000000..b728274
--- /dev/null
+++ b/board/gdsys/common/adv7611.c
@@ -0,0 +1,177 @@
+/*
+ * (C) Copyright 2014
+ * Dirk Eibach, Guntermann & Drunck GmbH, eibach@gdsys.de
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <i2c.h>
+
+#define ADV7611_I2C_ADDR 0x4c
+#define ADV7611_RDINFO 0x2051
+
+/*
+ * ADV7611 I2C Addresses in u-boot notation
+ */
+enum {
+	CP_I2C_ADDR = 0x22,
+	DPLL_I2C_ADDR = 0x26,
+	KSV_I2C_ADDR = 0x32,
+	HDMI_I2C_ADDR = 0x34,
+	EDID_I2C_ADDR = 0x36,
+	INFOFRAME_I2C_ADDR = 0x3e,
+	CEC_I2C_ADDR = 0x40,
+	IO_I2C_ADDR = ADV7611_I2C_ADDR,
+};
+
+/*
+ * Global Control Registers
+ */
+enum {
+	IO_RD_INFO_MSB = 0xea,
+	IO_RD_INFO_LSB = 0xeb,
+	IO_CEC_ADDR = 0xf4,
+	IO_INFOFRAME_ADDR = 0xf5,
+	IO_DPLL_ADDR = 0xf8,
+	IO_KSV_ADDR = 0xf9,
+	IO_EDID_ADDR = 0xfa,
+	IO_HDMI_ADDR = 0xfb,
+	IO_CP_ADDR = 0xfd,
+};
+
+int adv7611_i2c[] = CONFIG_SYS_ADV7611_I2C;
+
+int adv7611_probe(unsigned int screen)
+{
+	int old_bus = i2c_get_bus_num();
+	unsigned int rd_info;
+	int res = 0;
+
+	i2c_set_bus_num(adv7611_i2c[screen]);
+
+	rd_info = (i2c_reg_read(IO_I2C_ADDR, IO_RD_INFO_MSB) << 8)
+		  | i2c_reg_read(IO_I2C_ADDR, IO_RD_INFO_LSB);
+
+	if (rd_info != ADV7611_RDINFO) {
+		res = -1;
+		goto out;
+	}
+
+	/*
+	 * set I2C addresses to default values
+	 */
+	i2c_reg_write(IO_I2C_ADDR, IO_CEC_ADDR, CEC_I2C_ADDR << 1);
+	i2c_reg_write(IO_I2C_ADDR, IO_INFOFRAME_ADDR, INFOFRAME_I2C_ADDR << 1);
+	i2c_reg_write(IO_I2C_ADDR, IO_DPLL_ADDR, DPLL_I2C_ADDR << 1);
+	i2c_reg_write(IO_I2C_ADDR, IO_KSV_ADDR, KSV_I2C_ADDR << 1);
+	i2c_reg_write(IO_I2C_ADDR, IO_EDID_ADDR, EDID_I2C_ADDR << 1);
+	i2c_reg_write(IO_I2C_ADDR, IO_HDMI_ADDR, HDMI_I2C_ADDR << 1);
+	i2c_reg_write(IO_I2C_ADDR, IO_CP_ADDR, CP_I2C_ADDR << 1);
+
+	/*
+	 * do magic initialization sequence from
+	 * "ADV7611 Register Settings Recommendations Revision 1.5"
+	 * with most registers undocumented
+	 */
+	i2c_reg_write(CP_I2C_ADDR, 0x6c, 0x00);
+	i2c_reg_write(HDMI_I2C_ADDR, 0x9b, 0x03);
+	i2c_reg_write(HDMI_I2C_ADDR, 0x6f, 0x08);
+	i2c_reg_write(HDMI_I2C_ADDR, 0x85, 0x1f);
+	i2c_reg_write(HDMI_I2C_ADDR, 0x87, 0x70);
+	i2c_reg_write(HDMI_I2C_ADDR, 0x57, 0xda);
+	i2c_reg_write(HDMI_I2C_ADDR, 0x58, 0x01);
+	i2c_reg_write(HDMI_I2C_ADDR, 0x03, 0x98);
+	i2c_reg_write(HDMI_I2C_ADDR, 0x4c, 0x44);
+
+	/*
+	 * IO_REG_02, default 0xf0
+	 *
+	 * INP_COLOR_SPACE (IO, Address 0x02[7:4])
+	 * default: 0b1111 auto
+	 * set to : 0b0001 force RGB (range 0 to 255) input
+	 *
+	 * RGB_OUT (IO, Address 0x02[1])
+	 * default: 0 YPbPr color space output
+	 * set to : 1 RGB color space output
+	 */
+	i2c_reg_write(IO_I2C_ADDR, 0x02, 0x12);
+
+	/*
+	 * IO_REG_03, default 0x00
+	 *
+	 * OP_FORMAT_SEL (IO, Address 0x03[7:0])
+	 * default: 0x00 8-bit SDR ITU-656 mode
+	 * set to : 0x40 24-bit 4:4:4 SDR mode
+	 */
+	i2c_reg_write(IO_I2C_ADDR, 0x03, 0x40);
+
+	/*
+	 * IO_REG_05, default 0x2c
+	 *
+	 * AVCODE_INSERT_EN (IO, Address 0x05[2])
+	 * default: 1 insert AV codes into data stream
+	 * set to : 0 do not insert AV codes into data stream
+	 */
+	i2c_reg_write(IO_I2C_ADDR, 0x05, 0x28);
+
+	/*
+	 * IO_REG_0C, default 0x62
+	 *
+	 * POWER_DOWN (IO, Address 0x0C[5])
+	 * default: 1 chip is powered down
+	 * set to : 0 chip is operational
+	 */
+	i2c_reg_write(IO_I2C_ADDR, 0x0c, 0x42);
+
+	/*
+	 * IO_REG_15, default 0xbe
+	 *
+	 * TRI_SYNCS (IO, Address 0x15[3)
+	 * TRI_LLC (IO, Address 0x15[2])
+	 * TRI_PIX (IO, Address 0x15[1])
+	 * default: 1 video output pins are tristate
+	 * set to : 0 video output pins are active
+	 */
+	i2c_reg_write(IO_I2C_ADDR, 0x15, 0xb0);
+
+	/*
+	 * HDMI_REGISTER_02H, default 0xff
+	 *
+	 * CLOCK_TERMA_DISABLE (HDMI, Address 0x83[0])
+	 * default: 1 disable termination
+	 * set to : 0 enable termination
+	 * Future options are:
+	 * - use the chips automatic termination control
+	 * - set this manually on cable detect
+	 * but at the moment this seems a safe default.
+	 */
+	i2c_reg_write(HDMI_I2C_ADDR, 0x83, 0xfe);
+
+	/*
+	 * HDMI_CP_CNTRL_1, default 0x01
+	 *
+	 * HDMI_FRUN_EN (CP, Address 0xBA[0])
+	 * default: 1 Enable the free run feature in HDMI mode
+	 * set to : 0 Disable the free run feature in HDMI mode
+	 */
+	i2c_reg_write(CP_I2C_ADDR, 0xba, 0x00);
+
+	/*
+	 * INT1_CONFIGURATION, default 0x20
+	 *
+	 * INTRQ_DUR_SEL[1:0] (IO, Address 0x40[7:6])
+	 * default: 00 Interrupt signal is active for 4 Xtal periods
+	 * set to : 11 Active until cleared
+	 *
+	 * INTRQ_OP_SEL[1:0] (IO, Address 0x40[1:0])
+	 * default: 00 Open drain
+	 * set to : 10 Drives high when active
+	 */
+	i2c_reg_write(IO_I2C_ADDR, 0x40, 0xc2);
+
+out:
+	i2c_set_bus_num(old_bus);
+
+	return res;
+}
diff --git a/board/gdsys/common/adv7611.h b/board/gdsys/common/adv7611.h
new file mode 100644
index 0000000..25a8367
--- /dev/null
+++ b/board/gdsys/common/adv7611.h
@@ -0,0 +1,13 @@
+/*
+ * (C) Copyright 2014
+ * Dirk Eibach,  Guntermann & Drunck GmbH, dirk.eibach@gdsys.cc
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef _ADV7611_H_
+#define _ADV7611_H_
+
+int adv7611_probe(unsigned int screen);
+
+#endif
diff --git a/board/gdsys/common/ch7301.c b/board/gdsys/common/ch7301.c
new file mode 100644
index 0000000..c054e55
--- /dev/null
+++ b/board/gdsys/common/ch7301.c
@@ -0,0 +1,64 @@
+/*
+ * (C) Copyright 2014
+ * Dirk Eibach,  Guntermann & Drunck GmbH, dirk.eibach@gdsys.cc
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+/* Chrontel CH7301C DVI Transmitter */
+
+#include <common.h>
+#include <asm/io.h>
+#include <errno.h>
+#include <i2c.h>
+
+#define CH7301_I2C_ADDR 0x75
+
+enum {
+	CH7301_CM = 0x1c,		/* Clock Mode Register */
+	CH7301_IC = 0x1d,		/* Input Clock Register */
+	CH7301_GPIO = 0x1e,		/* GPIO Control Register */
+	CH7301_IDF = 0x1f,		/* Input Data Format Register */
+	CH7301_CD = 0x20,		/* Connection Detect Register */
+	CH7301_DC = 0x21,		/* DAC Control Register */
+	CH7301_HPD = 0x23,		/* Hot Plug Detection Register */
+	CH7301_TCTL = 0x31,		/* DVI Control Input Register */
+	CH7301_TPCP = 0x33,		/* DVI PLL Charge Pump Ctrl Register */
+	CH7301_TPD = 0x34,		/* DVI PLL Divide Register */
+	CH7301_TPVT = 0x35,		/* DVI PLL Supply Control Register */
+	CH7301_TPF = 0x36,		/* DVI PLL Filter Register */
+	CH7301_TCT = 0x37,		/* DVI Clock Test Register */
+	CH7301_TSTP = 0x48,		/* Test Pattern Register */
+	CH7301_PM = 0x49,		/* Power Management register */
+	CH7301_VID = 0x4a,		/* Version ID Register */
+	CH7301_DID = 0x4b,		/* Device ID Register */
+	CH7301_DSP = 0x56,		/* DVI Sync polarity Register */
+};
+
+int ch7301_i2c[] = CONFIG_SYS_CH7301_I2C;
+
+int ch7301_probe(unsigned screen, bool power)
+{
+	u8 value;
+
+	i2c_set_bus_num(ch7301_i2c[screen]);
+	if (i2c_probe(CH7301_I2C_ADDR))
+		return -1;
+
+	value = i2c_reg_read(CH7301_I2C_ADDR, CH7301_DID);
+	if (value != 0x17)
+		return -1;
+
+	if (power) {
+		i2c_reg_write(CH7301_I2C_ADDR, CH7301_TPCP, 0x08);
+		i2c_reg_write(CH7301_I2C_ADDR, CH7301_TPD, 0x16);
+		i2c_reg_write(CH7301_I2C_ADDR, CH7301_TPF, 0x60);
+		i2c_reg_write(CH7301_I2C_ADDR, CH7301_DC, 0x09);
+		i2c_reg_write(CH7301_I2C_ADDR, CH7301_PM, 0xc0);
+	} else {
+		i2c_reg_write(CH7301_I2C_ADDR, CH7301_DC, 0x00);
+		i2c_reg_write(CH7301_I2C_ADDR, CH7301_PM, 0x01);
+	}
+
+	return 0;
+}
diff --git a/board/gdsys/common/ch7301.h b/board/gdsys/common/ch7301.h
new file mode 100644
index 0000000..8383719
--- /dev/null
+++ b/board/gdsys/common/ch7301.h
@@ -0,0 +1,13 @@
+/*
+ * (C) Copyright 2014
+ * Dirk Eibach,  Guntermann & Drunck GmbH, dirk.eibach@gdsys.cc
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef _CH7301_H_
+#define _CH7301_H_
+
+int ch7301_probe(unsigned screen, bool power);
+
+#endif
diff --git a/board/gdsys/common/ioep-fpga.c b/board/gdsys/common/ioep-fpga.c
new file mode 100644
index 0000000..18d37dc
--- /dev/null
+++ b/board/gdsys/common/ioep-fpga.c
@@ -0,0 +1,227 @@
+/*
+ * (C) Copyright 2014
+ * Dirk Eibach,  Guntermann & Drunck GmbH, eibach@gdsys.de
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+
+#include <gdsys_fpga.h>
+
+enum {
+	UNITTYPE_MAIN_SERVER = 0,
+	UNITTYPE_MAIN_USER = 1,
+	UNITTYPE_VIDEO_SERVER = 2,
+	UNITTYPE_VIDEO_USER = 3,
+};
+
+enum {
+	UNITTYPEPCB_DVI = 0,
+	UNITTYPEPCB_DP_165 = 1,
+	UNITTYPEPCB_DP_300 = 2,
+	UNITTYPEPCB_HDMI = 3,
+};
+
+enum {
+	COMPRESSION_NONE = 0,
+	COMPRESSION_TYPE1_DELTA = 1,
+	COMPRESSION_TYPE1_TYPE2_DELTA = 3,
+};
+
+enum {
+	AUDIO_NONE = 0,
+	AUDIO_TX = 1,
+	AUDIO_RX = 2,
+	AUDIO_RXTX = 3,
+};
+
+enum {
+	SYSCLK_147456 = 0,
+};
+
+enum {
+	RAM_DDR2_32 = 0,
+	RAM_DDR3_32 = 1,
+};
+
+enum {
+	CARRIER_SPEED_1G = 0,
+	CARRIER_SPEED_2_5G = 1,
+};
+
+bool ioep_fpga_has_osd(unsigned int fpga)
+{
+	u16 fpga_features;
+	unsigned feature_osd;
+
+	FPGA_GET_REG(0, fpga_features, &fpga_features);
+	feature_osd = fpga_features & (1<<11);
+
+	return feature_osd;
+}
+
+void ioep_fpga_print_info(unsigned int fpga)
+{
+	u16 versions;
+	u16 fpga_version;
+	u16 fpga_features;
+	unsigned unit_type;
+	unsigned unit_type_pcb_video;
+	unsigned feature_compression;
+	unsigned feature_osd;
+	unsigned feature_audio;
+	unsigned feature_sysclock;
+	unsigned feature_ramconfig;
+	unsigned feature_carrier_speed;
+	unsigned feature_carriers;
+	unsigned feature_video_channels;
+
+	FPGA_GET_REG(fpga, versions, &versions);
+	FPGA_GET_REG(fpga, fpga_version, &fpga_version);
+	FPGA_GET_REG(fpga, fpga_features, &fpga_features);
+
+	unit_type = (versions & 0xf000) >> 12;
+	unit_type_pcb_video = (versions & 0x01c0) >> 6;
+	feature_compression = (fpga_features & 0xe000) >> 13;
+	feature_osd = fpga_features & (1<<11);
+	feature_audio = (fpga_features & 0x0600) >> 9;
+	feature_sysclock = (fpga_features & 0x0180) >> 7;
+	feature_ramconfig = (fpga_features & 0x0060) >> 5;
+	feature_carrier_speed = fpga_features & (1<<4);
+	feature_carriers = (fpga_features & 0x000c) >> 2;
+	feature_video_channels = fpga_features & 0x0003;
+
+	switch (unit_type) {
+	case UNITTYPE_MAIN_SERVER:
+	case UNITTYPE_MAIN_USER:
+		printf("Mainchannel");
+		break;
+
+	case UNITTYPE_VIDEO_SERVER:
+	case UNITTYPE_VIDEO_USER:
+		printf("Videochannel");
+		break;
+
+	default:
+		printf("UnitType %d(not supported)", unit_type);
+		break;
+	}
+
+	switch (unit_type) {
+	case UNITTYPE_MAIN_SERVER:
+	case UNITTYPE_VIDEO_SERVER:
+		printf(" Server");
+		if (versions & (1<<4))
+			printf(" UC");
+		break;
+
+	case UNITTYPE_MAIN_USER:
+	case UNITTYPE_VIDEO_USER:
+		printf(" User");
+		break;
+
+	default:
+		break;
+	}
+
+	if (versions & (1<<5))
+		printf(" Fiber");
+	else
+		printf(" CAT");
+
+	switch (unit_type_pcb_video) {
+	case UNITTYPEPCB_DVI:
+		printf(" DVI,");
+		break;
+
+	case UNITTYPEPCB_DP_165:
+		printf(" DP 165MPix/s,");
+		break;
+
+	case UNITTYPEPCB_DP_300:
+		printf(" DP 300MPix/s,");
+		break;
+
+	case UNITTYPEPCB_HDMI:
+		printf(" HDMI,");
+		break;
+	}
+
+	printf(" FPGA V %d.%02d\n       features:",
+	       fpga_version / 100, fpga_version % 100);
+
+
+	switch (feature_compression) {
+	case COMPRESSION_NONE:
+		printf(" no compression");
+		break;
+
+	case COMPRESSION_TYPE1_DELTA:
+		printf(" type1-deltacompression");
+		break;
+
+	case COMPRESSION_TYPE1_TYPE2_DELTA:
+		printf(" type1-deltacompression, type2-inlinecompression");
+		break;
+
+	default:
+		printf(" compression %d(not supported)", feature_compression);
+		break;
+	}
+
+	printf(", %sosd", feature_osd ? "" : "no ");
+
+	switch (feature_audio) {
+	case AUDIO_NONE:
+		printf(", no audio");
+		break;
+
+	case AUDIO_TX:
+		printf(", audio tx");
+		break;
+
+	case AUDIO_RX:
+		printf(", audio rx");
+		break;
+
+	case AUDIO_RXTX:
+		printf(", audio rx+tx");
+		break;
+
+	default:
+		printf(", audio %d(not supported)", feature_audio);
+		break;
+	}
+
+	puts(",\n       ");
+
+	switch (feature_sysclock) {
+	case SYSCLK_147456:
+		printf("clock 147.456 MHz");
+		break;
+
+	default:
+		printf("clock %d(not supported)", feature_sysclock);
+		break;
+	}
+
+	switch (feature_ramconfig) {
+	case RAM_DDR2_32:
+		printf(", RAM 32 bit DDR2");
+		break;
+
+	case RAM_DDR3_32:
+		printf(", RAM 32 bit DDR3");
+		break;
+
+	default:
+		printf(", RAM %d(not supported)", feature_ramconfig);
+		break;
+	}
+
+	printf(", %d carrier(s) %s", feature_carriers,
+	       feature_carrier_speed ? "2.5Gbit/s" : "1Gbit/s");
+
+	printf(", %d video channel(s)\n", feature_video_channels);
+}
diff --git a/board/gdsys/common/ioep-fpga.h b/board/gdsys/common/ioep-fpga.h
new file mode 100644
index 0000000..44f7139
--- /dev/null
+++ b/board/gdsys/common/ioep-fpga.h
@@ -0,0 +1,14 @@
+/*
+ * (C) Copyright 2014
+ * Dirk Eibach,  Guntermann & Drunck GmbH, dirk.eibach@gdsys.cc
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef _IOEP_FPGA_H_
+#define _IOEP_FPGA_H_
+
+void ioep_fpga_print_info(unsigned int fpga);
+bool ioep_fpga_has_osd(unsigned int fpga);
+
+#endif
diff --git a/board/gdsys/common/osd.c b/board/gdsys/common/osd.c
index 55ecdf1..f11e26f 100644
--- a/board/gdsys/common/osd.c
+++ b/board/gdsys/common/osd.c
@@ -9,11 +9,10 @@
 #include <i2c.h>
 #include <malloc.h>
 
+#include "ch7301.h"
 #include "dp501.h"
 #include <gdsys_fpga.h>
 
-#define CH7301_I2C_ADDR 0x75
-
 #define ICS8N3QV01_I2C_ADDR 0x6E
 #define ICS8N3QV01_FREF 114285000
 #define ICS8N3QV01_FREF_LL 114285000LL
@@ -29,27 +28,6 @@
 
 #define PIXCLK_640_480_60 25180000
 
-enum {
-	CH7301_CM = 0x1c,		/* Clock Mode Register */
-	CH7301_IC = 0x1d,		/* Input Clock Register */
-	CH7301_GPIO = 0x1e,		/* GPIO Control Register */
-	CH7301_IDF = 0x1f,		/* Input Data Format Register */
-	CH7301_CD = 0x20,		/* Connection Detect Register */
-	CH7301_DC = 0x21,		/* DAC Control Register */
-	CH7301_HPD = 0x23,		/* Hot Plug Detection Register */
-	CH7301_TCTL = 0x31,		/* DVI Control Input Register */
-	CH7301_TPCP = 0x33,		/* DVI PLL Charge Pump Ctrl Register */
-	CH7301_TPD = 0x34,		/* DVI PLL Divide Register */
-	CH7301_TPVT = 0x35,		/* DVI PLL Supply Control Register */
-	CH7301_TPF = 0x36,		/* DVI PLL Filter Register */
-	CH7301_TCT = 0x37,		/* DVI Clock Test Register */
-	CH7301_TSTP = 0x48,		/* Test Pattern Register */
-	CH7301_PM = 0x49,		/* Power Management register */
-	CH7301_VID = 0x4a,		/* Version ID Register */
-	CH7301_DID = 0x4b,		/* Device ID Register */
-	CH7301_DSP = 0x56,		/* DVI Sync polarity Register */
-};
-
 unsigned int base_width;
 unsigned int base_height;
 size_t bufsize;
@@ -61,10 +39,6 @@
 int ics8n3qv01_i2c[] = CONFIG_SYS_ICS8N3QV01_I2C;
 #endif
 
-#ifdef CONFIG_SYS_CH7301_I2C
-int ch7301_i2c[] = CONFIG_SYS_CH7301_I2C;
-#endif
-
 #ifdef CONFIG_SYS_SIL1178_I2C
 int sil1178_i2c[] = CONFIG_SYS_SIL1178_I2C;
 #endif
@@ -327,19 +301,8 @@
 	/* setup output driver */
 
 #ifdef CONFIG_SYS_CH7301_I2C
-	i2c_set_bus_num(ch7301_i2c[screen]);
-	if (!i2c_probe(CH7301_I2C_ADDR)) {
-		u8 value = i2c_reg_read(CH7301_I2C_ADDR, CH7301_DID);
-
-		if (value == 0x17) {
-			i2c_reg_write(CH7301_I2C_ADDR, CH7301_TPCP, 0x08);
-			i2c_reg_write(CH7301_I2C_ADDR, CH7301_TPD, 0x16);
-			i2c_reg_write(CH7301_I2C_ADDR, CH7301_TPF, 0x60);
-			i2c_reg_write(CH7301_I2C_ADDR, CH7301_DC, 0x09);
-			i2c_reg_write(CH7301_I2C_ADDR, CH7301_PM, 0xc0);
-			output_driver_present = true;
-		}
-	}
+	if (!ch7301_probe(screen, true))
+		output_driver_present = true;
 #endif
 
 #ifdef CONFIG_SYS_SIL1178_I2C
diff --git a/board/gdsys/common/osd.h b/board/gdsys/common/osd.h
index 440b276..5b3f14b 100644
--- a/board/gdsys/common/osd.h
+++ b/board/gdsys/common/osd.h
@@ -8,6 +8,7 @@
 #ifndef _OSD_H_
 #define _OSD_H_
 
+int ch7301_probe(unsigned screen, bool power);
 int osd_probe(unsigned screen);
 
 #endif
diff --git a/board/gdsys/mpc8308/Kconfig b/board/gdsys/mpc8308/Kconfig
index 43e1663..9a1a3a2 100644
--- a/board/gdsys/mpc8308/Kconfig
+++ b/board/gdsys/mpc8308/Kconfig
@@ -10,3 +10,16 @@
 	default "hrcon"
 
 endif
+
+if TARGET_STRIDER
+
+config SYS_BOARD
+	default "mpc8308"
+
+config SYS_VENDOR
+	default "gdsys"
+
+config SYS_CONFIG_NAME
+	default "strider"
+
+endif
diff --git a/board/gdsys/mpc8308/MAINTAINERS b/board/gdsys/mpc8308/MAINTAINERS
index a7853a5..35704bc 100644
--- a/board/gdsys/mpc8308/MAINTAINERS
+++ b/board/gdsys/mpc8308/MAINTAINERS
@@ -4,3 +4,6 @@
 F:	board/gdsys/mpc8308/
 F:	include/configs/hrcon.h
 F:	configs/hrcon_defconfig
+F:	include/configs/strider.h
+F:	configs/strider_cpu_defconfig
+F:	configs/strider_con_defconfig
diff --git a/board/gdsys/mpc8308/Makefile b/board/gdsys/mpc8308/Makefile
index b5dfdbb..42702fb 100644
--- a/board/gdsys/mpc8308/Makefile
+++ b/board/gdsys/mpc8308/Makefile
@@ -7,3 +7,4 @@
 
 obj-y := mpc8308.o sdram.o
 obj-$(CONFIG_HRCON) += hrcon.o
+obj-$(CONFIG_STRIDER) += strider.o
diff --git a/board/gdsys/mpc8308/strider.c b/board/gdsys/mpc8308/strider.c
new file mode 100644
index 0000000..8e5d5de
--- /dev/null
+++ b/board/gdsys/mpc8308/strider.c
@@ -0,0 +1,501 @@
+/*
+ * (C) Copyright 2014
+ * Dirk Eibach,  Guntermann & Drunck GmbH, eibach@gdsys.de
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <hwconfig.h>
+#include <i2c.h>
+#include <spi.h>
+#include <libfdt.h>
+#include <fdt_support.h>
+#include <pci.h>
+#include <mpc83xx.h>
+#include <fsl_esdhc.h>
+#include <asm/io.h>
+#include <asm/fsl_serdes.h>
+#include <asm/fsl_mpc83xx_serdes.h>
+
+#include "mpc8308.h"
+
+#include <gdsys_fpga.h>
+
+#include "../common/adv7611.h"
+#include "../common/ch7301.h"
+#include "../common/ioep-fpga.h"
+#include "../common/mclink.h"
+#include "../common/osd.h"
+#include "../common/phy.h"
+
+#include <pca953x.h>
+#include <pca9698.h>
+
+#include <miiphy.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define MAX_MUX_CHANNELS 2
+
+enum {
+	MCFPGA_DONE = 1 << 0,
+	MCFPGA_INIT_N = 1 << 1,
+	MCFPGA_PROGRAM_N = 1 << 2,
+	MCFPGA_UPDATE_ENABLE_N = 1 << 3,
+	MCFPGA_RESET_N = 1 << 4,
+};
+
+enum {
+	GPIO_MDC = 1 << 14,
+	GPIO_MDIO = 1 << 15,
+};
+
+enum {
+	FAN_CONFIG = 0x03,
+	FAN_TACHLIM_LSB = 0x48,
+	FAN_TACHLIM_MSB = 0x49,
+	FAN_PWM_FREQ = 0x4D,
+};
+
+unsigned int mclink_fpgacount;
+struct ihs_fpga *fpga_ptr[] = CONFIG_SYS_FPGA_PTR;
+
+struct {
+	u8 bus;
+	u8 addr;
+} strider_fans[] = CONFIG_STRIDER_FANS;
+
+int fpga_set_reg(u32 fpga, u16 *reg, off_t regoff, u16 data)
+{
+	int res;
+
+	switch (fpga) {
+	case 0:
+		out_le16(reg, data);
+		break;
+	default:
+		res = mclink_send(fpga - 1, regoff, data);
+		if (res < 0) {
+			printf("mclink_send reg %02lx data %04x returned %d\n",
+			       regoff, data, res);
+			return res;
+		}
+		break;
+	}
+
+	return 0;
+}
+
+int fpga_get_reg(u32 fpga, u16 *reg, off_t regoff, u16 *data)
+{
+	int res;
+
+	switch (fpga) {
+	case 0:
+		*data = in_le16(reg);
+		break;
+	default:
+		if (fpga > mclink_fpgacount)
+			return -EINVAL;
+		res = mclink_receive(fpga - 1, regoff, data);
+		if (res < 0) {
+			printf("mclink_receive reg %02lx returned %d\n",
+			       regoff, res);
+			return res;
+		}
+	}
+
+	return 0;
+}
+
+int checkboard(void)
+{
+	char *s = getenv("serial#");
+	bool hw_type_cat = pca9698_get_value(0x20, 18);
+
+	puts("Board: ");
+
+	printf("Strider %s", hw_type_cat ? "CAT" : "Fiber");
+
+	if (s != NULL) {
+		puts(", serial# ");
+		puts(s);
+	}
+
+	puts("\n");
+
+	return 0;
+}
+
+static void init_fan_controller(u8 addr)
+{
+	int val;
+
+	/* set PWM Frequency to 2.5% resolution */
+	i2c_reg_write(addr, FAN_PWM_FREQ, 20);
+
+	/* set Tachometer Limit */
+	i2c_reg_write(addr, FAN_TACHLIM_LSB, 0x10);
+	i2c_reg_write(addr, FAN_TACHLIM_MSB, 0x0a);
+
+	/* enable Tach input */
+	val = i2c_reg_read(addr, FAN_CONFIG) | 0x04;
+	i2c_reg_write(addr, FAN_CONFIG, val);
+}
+
+int last_stage_init(void)
+{
+	int slaves;
+	unsigned int k;
+	unsigned int mux_ch;
+	unsigned char mclink_controllers[] = { 0x3c, 0x3d, 0x3e };
+	bool hw_type_cat = pca9698_get_value(0x20, 18);
+	bool ch0_sgmii2_present = false;
+
+	/* Turn on Analog Devices ADV7611 */
+	pca9698_direction_output(0x20, 8, 0);
+
+	/* Turn on Parade DP501 */
+	pca9698_direction_output(0x20, 9, 1);
+
+	ch0_sgmii2_present = !pca9698_get_value(0x20, 37);
+
+	/* wait for FPGA done, then reset FPGA */
+	for (k = 0; k < ARRAY_SIZE(mclink_controllers); ++k) {
+		unsigned int ctr = 0;
+
+		if (i2c_probe(mclink_controllers[k]))
+			continue;
+
+		while (!(pca953x_get_val(mclink_controllers[k])
+		       & MCFPGA_DONE)) {
+			udelay(100000);
+			if (ctr++ > 5) {
+				printf("no done for mclink_controller %d\n", k);
+				break;
+			}
+		}
+
+		pca953x_set_dir(mclink_controllers[k], MCFPGA_RESET_N, 0);
+		pca953x_set_val(mclink_controllers[k], MCFPGA_RESET_N, 0);
+		udelay(10);
+		pca953x_set_val(mclink_controllers[k], MCFPGA_RESET_N,
+				MCFPGA_RESET_N);
+	}
+
+	if (hw_type_cat) {
+		miiphy_register(bb_miiphy_buses[0].name, bb_miiphy_read,
+				bb_miiphy_write);
+		for (mux_ch = 0; mux_ch < MAX_MUX_CHANNELS; ++mux_ch) {
+			if ((mux_ch == 1) && !ch0_sgmii2_present)
+				continue;
+
+			setup_88e1514(bb_miiphy_buses[0].name, mux_ch);
+		}
+	}
+
+	/* give slave-PLLs and Parade DP501 some time to be up and running */
+	udelay(500000);
+
+	mclink_fpgacount = CONFIG_SYS_MCLINK_MAX;
+	slaves = mclink_probe();
+	mclink_fpgacount = 0;
+
+	ioep_fpga_print_info(0);
+
+	if (!adv7611_probe(0))
+		printf("       Advantiv ADV7611 HDMI Receiver\n");
+
+#ifdef CONFIG_STRIDER_CON
+	if (ioep_fpga_has_osd(0))
+		osd_probe(0);
+#endif
+
+#ifdef CONFIG_STRIDER_CPU
+	ch7301_probe(0, false);
+#endif
+
+	if (slaves <= 0)
+		return 0;
+
+	mclink_fpgacount = slaves;
+
+	for (k = 1; k <= slaves; ++k) {
+		ioep_fpga_print_info(k);
+#ifdef CONFIG_STRIDER_CON
+		if (ioep_fpga_has_osd(k))
+			osd_probe(k);
+#endif
+#ifdef CONFIG_STRIDER_CPU
+		FPGA_SET_REG(k, extended_control, 0); /* enable video in*/
+		if (!adv7611_probe(k))
+			printf("       Advantiv ADV7611 HDMI Receiver\n");
+		ch7301_probe(k, false);
+#endif
+		if (hw_type_cat) {
+			miiphy_register(bb_miiphy_buses[k].name,
+					bb_miiphy_read, bb_miiphy_write);
+			setup_88e1514(bb_miiphy_buses[k].name, 0);
+		}
+	}
+
+	for (k = 0; k < ARRAY_SIZE(strider_fans); ++k) {
+		i2c_set_bus_num(strider_fans[k].bus);
+		init_fan_controller(strider_fans[k].addr);
+	}
+
+	return 0;
+}
+
+/*
+ * provide access to fpga gpios (for I2C bitbang)
+ * (these may look all too simple but make iocon.h much more readable)
+ */
+void fpga_gpio_set(unsigned int bus, int pin)
+{
+	FPGA_SET_REG(bus, gpio.set, pin);
+}
+
+void fpga_gpio_clear(unsigned int bus, int pin)
+{
+	FPGA_SET_REG(bus, gpio.clear, pin);
+}
+
+int fpga_gpio_get(unsigned int bus, int pin)
+{
+	u16 val;
+
+	FPGA_GET_REG(bus, gpio.read, &val);
+
+	return val & pin;
+}
+
+void mpc8308_init(void)
+{
+	pca9698_direction_output(0x20, 26, 1);
+}
+
+void mpc8308_set_fpga_reset(unsigned state)
+{
+	pca9698_set_value(0x20, 26, state ? 0 : 1);
+}
+
+void mpc8308_setup_hw(void)
+{
+	immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
+
+	/*
+	 * set "startup-finished"-gpios
+	 */
+	setbits_be32(&immr->gpio[0].dir, (1 << (31-11)) | (1 << (31-12)));
+	setbits_be32(&immr->gpio[0].dat, 1 << (31-12));
+}
+
+int mpc8308_get_fpga_done(unsigned fpga)
+{
+	return pca9698_get_value(0x20, 20);
+}
+
+#ifdef CONFIG_FSL_ESDHC
+int board_mmc_init(bd_t *bd)
+{
+	immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
+	sysconf83xx_t *sysconf = &immr->sysconf;
+
+	/* Enable cache snooping in eSDHC system configuration register */
+	out_be32(&sysconf->sdhccr, 0x02000000);
+
+	return fsl_esdhc_mmc_init(bd);
+}
+#endif
+
+static struct pci_region pcie_regions_0[] = {
+	{
+		.bus_start = CONFIG_SYS_PCIE1_MEM_BASE,
+		.phys_start = CONFIG_SYS_PCIE1_MEM_PHYS,
+		.size = CONFIG_SYS_PCIE1_MEM_SIZE,
+		.flags = PCI_REGION_MEM,
+	},
+	{
+		.bus_start = CONFIG_SYS_PCIE1_IO_BASE,
+		.phys_start = CONFIG_SYS_PCIE1_IO_PHYS,
+		.size = CONFIG_SYS_PCIE1_IO_SIZE,
+		.flags = PCI_REGION_IO,
+	},
+};
+
+void pci_init_board(void)
+{
+	immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
+	sysconf83xx_t *sysconf = &immr->sysconf;
+	law83xx_t *pcie_law = sysconf->pcielaw;
+	struct pci_region *pcie_reg[] = { pcie_regions_0 };
+
+	fsl_setup_serdes(CONFIG_FSL_SERDES1, FSL_SERDES_PROTO_PEX,
+			 FSL_SERDES_CLK_100, FSL_SERDES_VDD_1V);
+
+	/* Deassert the resets in the control register */
+	out_be32(&sysconf->pecr1, 0xE0008000);
+	udelay(2000);
+
+	/* Configure PCI Express Local Access Windows */
+	out_be32(&pcie_law[0].bar, CONFIG_SYS_PCIE1_BASE & LAWBAR_BAR);
+	out_be32(&pcie_law[0].ar, LBLAWAR_EN | LBLAWAR_512MB);
+
+	mpc83xx_pcie_init(1, pcie_reg);
+}
+
+ulong board_flash_get_legacy(ulong base, int banknum, flash_info_t *info)
+{
+	info->portwidth = FLASH_CFI_16BIT;
+	info->chipwidth = FLASH_CFI_BY16;
+	info->interface = FLASH_CFI_X16;
+	return 1;
+}
+
+#if defined(CONFIG_OF_BOARD_SETUP)
+int ft_board_setup(void *blob, bd_t *bd)
+{
+	ft_cpu_setup(blob, bd);
+	fdt_fixup_dr_usb(blob, bd);
+	fdt_fixup_esdhc(blob, bd);
+
+	return 0;
+}
+#endif
+
+/*
+ * FPGA MII bitbang implementation
+ */
+
+struct fpga_mii {
+	unsigned fpga;
+	int mdio;
+} fpga_mii[] = {
+	{ 0, 1},
+	{ 1, 1},
+	{ 2, 1},
+	{ 3, 1},
+};
+
+static int mii_dummy_init(struct bb_miiphy_bus *bus)
+{
+	return 0;
+}
+
+static int mii_mdio_active(struct bb_miiphy_bus *bus)
+{
+	struct fpga_mii *fpga_mii = bus->priv;
+
+	if (fpga_mii->mdio)
+		FPGA_SET_REG(fpga_mii->fpga, gpio.set, GPIO_MDIO);
+	else
+		FPGA_SET_REG(fpga_mii->fpga, gpio.clear, GPIO_MDIO);
+
+	return 0;
+}
+
+static int mii_mdio_tristate(struct bb_miiphy_bus *bus)
+{
+	struct fpga_mii *fpga_mii = bus->priv;
+
+	FPGA_SET_REG(fpga_mii->fpga, gpio.set, GPIO_MDIO);
+
+	return 0;
+}
+
+static int mii_set_mdio(struct bb_miiphy_bus *bus, int v)
+{
+	struct fpga_mii *fpga_mii = bus->priv;
+
+	if (v)
+		FPGA_SET_REG(fpga_mii->fpga, gpio.set, GPIO_MDIO);
+	else
+		FPGA_SET_REG(fpga_mii->fpga, gpio.clear, GPIO_MDIO);
+
+	fpga_mii->mdio = v;
+
+	return 0;
+}
+
+static int mii_get_mdio(struct bb_miiphy_bus *bus, int *v)
+{
+	u16 gpio;
+	struct fpga_mii *fpga_mii = bus->priv;
+
+	FPGA_GET_REG(fpga_mii->fpga, gpio.read, &gpio);
+
+	*v = ((gpio & GPIO_MDIO) != 0);
+
+	return 0;
+}
+
+static int mii_set_mdc(struct bb_miiphy_bus *bus, int v)
+{
+	struct fpga_mii *fpga_mii = bus->priv;
+
+	if (v)
+		FPGA_SET_REG(fpga_mii->fpga, gpio.set, GPIO_MDC);
+	else
+		FPGA_SET_REG(fpga_mii->fpga, gpio.clear, GPIO_MDC);
+
+	return 0;
+}
+
+static int mii_delay(struct bb_miiphy_bus *bus)
+{
+	udelay(1);
+
+	return 0;
+}
+
+struct bb_miiphy_bus bb_miiphy_buses[] = {
+	{
+		.name = "board0",
+		.init = mii_dummy_init,
+		.mdio_active = mii_mdio_active,
+		.mdio_tristate = mii_mdio_tristate,
+		.set_mdio = mii_set_mdio,
+		.get_mdio = mii_get_mdio,
+		.set_mdc = mii_set_mdc,
+		.delay = mii_delay,
+		.priv = &fpga_mii[0],
+	},
+	{
+		.name = "board1",
+		.init = mii_dummy_init,
+		.mdio_active = mii_mdio_active,
+		.mdio_tristate = mii_mdio_tristate,
+		.set_mdio = mii_set_mdio,
+		.get_mdio = mii_get_mdio,
+		.set_mdc = mii_set_mdc,
+		.delay = mii_delay,
+		.priv = &fpga_mii[1],
+	},
+	{
+		.name = "board2",
+		.init = mii_dummy_init,
+		.mdio_active = mii_mdio_active,
+		.mdio_tristate = mii_mdio_tristate,
+		.set_mdio = mii_set_mdio,
+		.get_mdio = mii_get_mdio,
+		.set_mdc = mii_set_mdc,
+		.delay = mii_delay,
+		.priv = &fpga_mii[2],
+	},
+	{
+		.name = "board3",
+		.init = mii_dummy_init,
+		.mdio_active = mii_mdio_active,
+		.mdio_tristate = mii_mdio_tristate,
+		.set_mdio = mii_set_mdio,
+		.get_mdio = mii_get_mdio,
+		.set_mdc = mii_set_mdc,
+		.delay = mii_delay,
+		.priv = &fpga_mii[3],
+	},
+};
+
+int bb_miiphy_buses_num = sizeof(bb_miiphy_buses) /
+			  sizeof(bb_miiphy_buses[0]);
diff --git a/configs/strider_con_defconfig b/configs/strider_con_defconfig
new file mode 100644
index 0000000..74ef69e
--- /dev/null
+++ b/configs/strider_con_defconfig
@@ -0,0 +1,7 @@
+CONFIG_SYS_EXTRA_OPTIONS="STRIDER_CON"
+CONFIG_PPC=y
+CONFIG_MPC83xx=y
+CONFIG_TARGET_STRIDER=y
+CONFIG_AUTOBOOT_KEYED=y
+CONFIG_AUTOBOOT_STOP_STR=" "
+# CONFIG_CMD_SETEXPR is not set
diff --git a/configs/strider_cpu_defconfig b/configs/strider_cpu_defconfig
new file mode 100644
index 0000000..fc0a823
--- /dev/null
+++ b/configs/strider_cpu_defconfig
@@ -0,0 +1,7 @@
+CONFIG_SYS_EXTRA_OPTIONS="STRIDER_CPU"
+CONFIG_PPC=y
+CONFIG_MPC83xx=y
+CONFIG_TARGET_STRIDER=y
+CONFIG_AUTOBOOT_KEYED=y
+CONFIG_AUTOBOOT_STOP_STR=" "
+# CONFIG_CMD_SETEXPR is not set
diff --git a/include/configs/strider.h b/include/configs/strider.h
new file mode 100644
index 0000000..fb7b7f9
--- /dev/null
+++ b/include/configs/strider.h
@@ -0,0 +1,651 @@
+/*
+ * (C) Copyright 2014
+ * Dirk Eibach,  Guntermann & Drunck GmbH, eibach@gdsys.de
+ *
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_E300		1 /* E300 family */
+#define CONFIG_MPC83xx		1 /* MPC83xx family */
+#define CONFIG_MPC830x		1 /* MPC830x family */
+#define CONFIG_MPC8308		1 /* MPC8308 CPU specific */
+#define CONFIG_STRIDER		1 /* STRIDER board specific */
+
+#define	CONFIG_SYS_TEXT_BASE	0xFE000000
+
+#ifdef CONFIG_STRIDER_CPU
+#define CONFIG_IDENT_STRING	" strider cpu 0.01"
+#else
+#define CONFIG_IDENT_STRING	" strider con 0.01"
+#endif
+
+#define CONFIG_BOARD_EARLY_INIT_F
+#define CONFIG_BOARD_EARLY_INIT_R
+#define CONFIG_LAST_STAGE_INIT
+
+/* new uImage format support */
+#define CONFIG_FIT			1
+#define CONFIG_FIT_VERBOSE		1
+
+#define CONFIG_MMC
+#define CONFIG_FSL_ESDHC
+#define CONFIG_SYS_FSL_ESDHC_ADDR	CONFIG_SYS_MPC83xx_ESDHC_ADDR
+#define CONFIG_SYS_FSL_ERRATUM_ESDHC111
+
+#define CONFIG_CMD_MMC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_DOS_PARTITION
+#define CONFIG_CMD_EXT2
+
+#define CONFIG_CMD_MEMTEST
+#define CONFIG_SYS_ALT_MEMTEST
+
+#define CONFIG_CMD_FPGAD
+#define CONFIG_CMD_IOLOOP
+
+/*
+ * System Clock Setup
+ */
+#define CONFIG_83XX_CLKIN	33333333 /* in Hz */
+#define CONFIG_SYS_CLK_FREQ	CONFIG_83XX_CLKIN
+
+/*
+ * Hardware Reset Configuration Word
+ * if CLKIN is 66.66MHz, then
+ * CSB = 133MHz, DDRC = 266MHz, LBC = 133MHz
+ * We choose the A type silicon as default, so the core is 400Mhz.
+ */
+#define CONFIG_SYS_HRCW_LOW (\
+	HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
+	HRCWL_DDR_TO_SCB_CLK_2X1 |\
+	HRCWL_SVCOD_DIV_2 |\
+	HRCWL_CSB_TO_CLKIN_4X1 |\
+	HRCWL_CORE_TO_CSB_3X1)
+/*
+ * There are neither HRCWH_PCI_HOST nor HRCWH_PCI1_ARBITER_ENABLE bits
+ * in 8308's HRCWH according to the manual, but original Freescale's
+ * code has them and I've expirienced some problems using the board
+ * with BDI3000 attached when I've tried to set these bits to zero
+ * (UART doesn't work after the 'reset run' command).
+ */
+#define CONFIG_SYS_HRCW_HIGH (\
+	HRCWH_PCI_HOST |\
+	HRCWH_PCI1_ARBITER_ENABLE |\
+	HRCWH_CORE_ENABLE |\
+	HRCWH_FROM_0XFFF00100 |\
+	HRCWH_BOOTSEQ_DISABLE |\
+	HRCWH_SW_WATCHDOG_DISABLE |\
+	HRCWH_ROM_LOC_LOCAL_16BIT |\
+	HRCWH_RL_EXT_LEGACY |\
+	HRCWH_TSEC1M_IN_MII |\
+	HRCWH_TSEC2M_IN_RGMII |\
+	HRCWH_BIG_ENDIAN)
+
+/*
+ * System IO Config
+ */
+#define CONFIG_SYS_SICRH (\
+	SICRH_ESDHC_A_SD |\
+	SICRH_ESDHC_B_SD |\
+	SICRH_ESDHC_C_SD |\
+	SICRH_GPIO_A_GPIO |\
+	SICRH_GPIO_B_GPIO |\
+	SICRH_IEEE1588_A_GPIO |\
+	SICRH_USB |\
+	SICRH_GTM_GPIO |\
+	SICRH_IEEE1588_B_GPIO |\
+	SICRH_ETSEC2_GPIO |\
+	SICRH_GPIOSEL_1 |\
+	SICRH_TMROBI_V3P3 |\
+	SICRH_TSOBI1_V2P5 |\
+	SICRH_TSOBI2_V2P5)	/* 0x0037f103 */
+#define CONFIG_SYS_SICRL (\
+	SICRL_SPI_PF0 |\
+	SICRL_UART_PF0 |\
+	SICRL_IRQ_PF0 |\
+	SICRL_I2C2_PF0 |\
+	SICRL_ETSEC1_TX_CLK)	/* 0x00000000 */
+
+/*
+ * IMMR new address
+ */
+#define CONFIG_SYS_IMMR		0xE0000000
+
+/*
+ * SERDES
+ */
+#define CONFIG_FSL_SERDES
+#define CONFIG_FSL_SERDES1	0xe3000
+
+/*
+ * Arbiter Setup
+ */
+#define CONFIG_SYS_ACR_PIPE_DEP	3 /* Arbiter pipeline depth is 4 */
+#define CONFIG_SYS_ACR_RPTCNT	3 /* Arbiter repeat count is 4 */
+#define CONFIG_SYS_SPCR_TSECEP	3 /* eTSEC emergency priority is highest */
+
+/*
+ * DDR Setup
+ */
+#define CONFIG_SYS_DDR_BASE		0x00000000 /* DDR is system memory */
+#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_BASE
+#define CONFIG_SYS_DDR_SDRAM_BASE	CONFIG_SYS_DDR_BASE
+#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL	DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
+#define CONFIG_SYS_DDRCDR_VALUE	(DDRCDR_EN \
+				| DDRCDR_PZ_LOZ \
+				| DDRCDR_NZ_LOZ \
+				| DDRCDR_ODT \
+				| DDRCDR_Q_DRN)
+				/* 0x7b880001 */
+/*
+ * Manually set up DDR parameters
+ * consist of one chip NT5TU64M16HG from NANYA
+ */
+
+#define CONFIG_SYS_DDR_SIZE		128 /* MB */
+
+#define CONFIG_SYS_DDR_CS0_BNDS	0x00000007
+#define CONFIG_SYS_DDR_CS0_CONFIG	(CSCONFIG_EN \
+				| CSCONFIG_ODT_RD_NEVER \
+				| CSCONFIG_ODT_WR_ONLY_CURRENT \
+				| CSCONFIG_BANK_BIT_3 \
+				| CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_10)
+				/* 0x80010102 */
+#define CONFIG_SYS_DDR_TIMING_3	0
+#define CONFIG_SYS_DDR_TIMING_0	((0 << TIMING_CFG0_RWT_SHIFT) \
+				| (0 << TIMING_CFG0_WRT_SHIFT) \
+				| (0 << TIMING_CFG0_RRT_SHIFT) \
+				| (0 << TIMING_CFG0_WWT_SHIFT) \
+				| (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \
+				| (6 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \
+				| (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \
+				| (2 << TIMING_CFG0_MRS_CYC_SHIFT))
+				/* 0x00260802 */
+#define CONFIG_SYS_DDR_TIMING_1	((2 << TIMING_CFG1_PRETOACT_SHIFT) \
+				| (6 << TIMING_CFG1_ACTTOPRE_SHIFT) \
+				| (2 << TIMING_CFG1_ACTTORW_SHIFT) \
+				| (7 << TIMING_CFG1_CASLAT_SHIFT) \
+				| (9 << TIMING_CFG1_REFREC_SHIFT) \
+				| (2 << TIMING_CFG1_WRREC_SHIFT) \
+				| (2 << TIMING_CFG1_ACTTOACT_SHIFT) \
+				| (2 << TIMING_CFG1_WRTORD_SHIFT))
+				/* 0x26279222 */
+#define CONFIG_SYS_DDR_TIMING_2	((0 << TIMING_CFG2_ADD_LAT_SHIFT) \
+				| (4 << TIMING_CFG2_CPO_SHIFT) \
+				| (3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \
+				| (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \
+				| (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \
+				| (3 << TIMING_CFG2_CKE_PLS_SHIFT) \
+				| (5 << TIMING_CFG2_FOUR_ACT_SHIFT))
+				/* 0x021848c5 */
+#define CONFIG_SYS_DDR_INTERVAL	((0x0824 << SDRAM_INTERVAL_REFINT_SHIFT) \
+				| (0x0100 << SDRAM_INTERVAL_BSTOPRE_SHIFT))
+				/* 0x08240100 */
+#define CONFIG_SYS_DDR_SDRAM_CFG	(SDRAM_CFG_SREN \
+				| SDRAM_CFG_SDRAM_TYPE_DDR2 \
+				| SDRAM_CFG_DBW_16)
+				/* 0x43100000 */
+
+#define CONFIG_SYS_DDR_SDRAM_CFG2	0x00401000 /* 1 posted refresh */
+#define CONFIG_SYS_DDR_MODE		((0x0440 << SDRAM_MODE_ESD_SHIFT) \
+				| (0x0242 << SDRAM_MODE_SD_SHIFT))
+				/* ODT 150ohm CL=4, AL=0 on SDRAM */
+#define CONFIG_SYS_DDR_MODE2		0x00000000
+
+/*
+ * Memory test
+ */
+#define CONFIG_SYS_MEMTEST_START	0x00001000 /* memtest region */
+#define CONFIG_SYS_MEMTEST_END		0x07f00000
+
+/*
+ * The reserved memory
+ */
+#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE /* start of monitor */
+
+#define CONFIG_SYS_MONITOR_LEN	(384 * 1024) /* Reserve 384 kB for Mon */
+#define CONFIG_SYS_MALLOC_LEN	(512 * 1024) /* Reserved for malloc */
+
+/*
+ * Initial RAM Base Address Setup
+ */
+#define CONFIG_SYS_INIT_RAM_LOCK	1
+#define CONFIG_SYS_INIT_RAM_ADDR	0xE6000000 /* Initial RAM address */
+#define CONFIG_SYS_INIT_RAM_SIZE	0x1000 /* Size of used area in RAM */
+#define CONFIG_SYS_GBL_DATA_OFFSET	\
+	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+
+/*
+ * Local Bus Configuration & Clock Setup
+ */
+#define CONFIG_SYS_LCRR_DBYP		LCRR_DBYP
+#define CONFIG_SYS_LCRR_CLKDIV		LCRR_CLKDIV_2
+#define CONFIG_SYS_LBC_LBCR		0x00040000
+
+/*
+ * FLASH on the Local Bus
+ */
+#if 1
+#define CONFIG_SYS_FLASH_CFI		/* use the Common Flash Interface */
+#define CONFIG_FLASH_CFI_DRIVER		/* use the CFI driver */
+#define CONFIG_SYS_FLASH_CFI_WIDTH	FLASH_CFI_16BIT
+#define CONFIG_FLASH_CFI_LEGACY
+#define CONFIG_SYS_FLASH_LEGACY_512Kx16
+#else
+#define CONFIG_SYS_NO_FLASH
+#endif
+
+#define CONFIG_SYS_FLASH_BASE		0xFE000000 /* FLASH base address */
+#define CONFIG_SYS_FLASH_SIZE		8 /* FLASH size is up to 8M */
+#define CONFIG_SYS_FLASH_PROTECTION	1 /* Use h/w Flash protection. */
+
+/* Window base at flash base */
+#define CONFIG_SYS_LBLAWBAR0_PRELIM	CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_LBLAWAR0_PRELIM	(LBLAWAR_EN | LBLAWAR_8MB)
+
+#define CONFIG_SYS_BR0_PRELIM	(CONFIG_SYS_FLASH_BASE \
+				| BR_PS_16	/* 16 bit port */ \
+				| BR_MS_GPCM	/* MSEL = GPCM */ \
+				| BR_V)		/* valid */
+#define CONFIG_SYS_OR0_PRELIM	(MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
+				| OR_UPM_XAM \
+				| OR_GPCM_CSNT \
+				| OR_GPCM_ACS_DIV2 \
+				| OR_GPCM_XACS \
+				| OR_GPCM_SCY_15 \
+				| OR_GPCM_TRLX_SET \
+				| OR_GPCM_EHTR_SET)
+
+#define CONFIG_SYS_MAX_FLASH_BANKS	1 /* number of banks */
+#define CONFIG_SYS_MAX_FLASH_SECT	135
+
+#define CONFIG_SYS_FLASH_ERASE_TOUT	60000 /* Flash Erase Timeout (ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT	500 /* Flash Write Timeout (ms) */
+
+/*
+ * FPGA
+ */
+#define CONFIG_SYS_FPGA0_BASE		0xE0600000
+#define CONFIG_SYS_FPGA0_SIZE		1 /* FPGA size is 1M */
+
+/* Window base at FPGA base */
+#define CONFIG_SYS_LBLAWBAR1_PRELIM	CONFIG_SYS_FPGA0_BASE
+#define CONFIG_SYS_LBLAWAR1_PRELIM	(LBLAWAR_EN | LBLAWAR_1MB)
+
+#define CONFIG_SYS_BR1_PRELIM	(CONFIG_SYS_FPGA0_BASE \
+				| BR_PS_16	/* 16 bit port */ \
+				| BR_MS_GPCM	/* MSEL = GPCM */ \
+				| BR_V)		/* valid */
+#define CONFIG_SYS_OR1_PRELIM	(MEG_TO_AM(CONFIG_SYS_FPGA0_SIZE) \
+				| OR_UPM_XAM \
+				| OR_GPCM_CSNT \
+				| OR_GPCM_ACS_DIV2 \
+				| OR_GPCM_XACS \
+				| OR_GPCM_SCY_15 \
+				| OR_GPCM_TRLX_SET \
+				| OR_GPCM_EHTR_SET)
+
+#define CONFIG_SYS_FPGA_BASE(k)		CONFIG_SYS_FPGA0_BASE
+#define CONFIG_SYS_FPGA_DONE(k)		0x0010
+
+#define CONFIG_SYS_FPGA_COUNT		1
+
+#define CONFIG_SYS_MCLINK_MAX		3
+
+#define CONFIG_SYS_FPGA_PTR \
+	{ (struct ihs_fpga *)CONFIG_SYS_FPGA0_BASE, NULL, NULL, NULL }
+
+#define CONFIG_SYS_FPGA_NO_RFL_HI
+
+/*
+ * Serial Port
+ */
+#define CONFIG_CONS_INDEX	2
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE	1
+#define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
+
+#define CONFIG_SYS_BAUDRATE_TABLE  \
+	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
+
+#define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_IMMR + 0x4500)
+#define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_IMMR + 0x4600)
+
+/* Use the HUSH parser */
+#define CONFIG_SYS_HUSH_PARSER
+
+/* Pass open firmware flat tree */
+#define CONFIG_OF_LIBFDT		1
+#define CONFIG_OF_BOARD_SETUP		1
+#define CONFIG_OF_STDOUT_VIA_ALIAS	1
+
+/* I2C */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED	400000
+#define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET	0x3000
+
+#define CONFIG_PCA953X			/* NXP PCA9554 */
+#define CONFIG_PCA9698			/* NXP PCA9698 */
+
+#define CONFIG_SYS_I2C_IHS
+#define CONFIG_SYS_I2C_IHS_CH0
+#define CONFIG_SYS_I2C_IHS_SPEED_0		50000
+#define CONFIG_SYS_I2C_IHS_SLAVE_0		0x7F
+#define CONFIG_SYS_I2C_IHS_CH1
+#define CONFIG_SYS_I2C_IHS_SPEED_1		50000
+#define CONFIG_SYS_I2C_IHS_SLAVE_1		0x7F
+#define CONFIG_SYS_I2C_IHS_CH2
+#define CONFIG_SYS_I2C_IHS_SPEED_2		50000
+#define CONFIG_SYS_I2C_IHS_SLAVE_2		0x7F
+#define CONFIG_SYS_I2C_IHS_CH3
+#define CONFIG_SYS_I2C_IHS_SPEED_3		50000
+#define CONFIG_SYS_I2C_IHS_SLAVE_3		0x7F
+
+/*
+ * Software (bit-bang) I2C driver configuration
+ */
+#define CONFIG_SYS_I2C_SOFT
+#define CONFIG_SOFT_I2C_READ_REPEATED_START
+#define CONFIG_SYS_I2C_SOFT_SPEED		50000
+#define CONFIG_SYS_I2C_SOFT_SLAVE		0x7F
+#define I2C_SOFT_DECLARATIONS2
+#define CONFIG_SYS_I2C_SOFT_SPEED_2		50000
+#define CONFIG_SYS_I2C_SOFT_SLAVE_2		0x7F
+#define I2C_SOFT_DECLARATIONS3
+#define CONFIG_SYS_I2C_SOFT_SPEED_3		50000
+#define CONFIG_SYS_I2C_SOFT_SLAVE_3		0x7F
+#define I2C_SOFT_DECLARATIONS4
+#define CONFIG_SYS_I2C_SOFT_SPEED_4		50000
+#define CONFIG_SYS_I2C_SOFT_SLAVE_4		0x7F
+#ifdef CONFIG_STRIDER_CON
+#define I2C_SOFT_DECLARATIONS5
+#define CONFIG_SYS_I2C_SOFT_SPEED_5		50000
+#define CONFIG_SYS_I2C_SOFT_SLAVE_5		0x7F
+#define I2C_SOFT_DECLARATIONS6
+#define CONFIG_SYS_I2C_SOFT_SPEED_6		50000
+#define CONFIG_SYS_I2C_SOFT_SLAVE_6		0x7F
+#define I2C_SOFT_DECLARATIONS7
+#define CONFIG_SYS_I2C_SOFT_SPEED_7		50000
+#define CONFIG_SYS_I2C_SOFT_SLAVE_7		0x7F
+#define I2C_SOFT_DECLARATIONS8
+#define CONFIG_SYS_I2C_SOFT_SPEED_8		50000
+#define CONFIG_SYS_I2C_SOFT_SLAVE_8		0x7F
+#endif
+
+#ifdef CONFIG_STRIDER_CON
+#define CONFIG_SYS_ICS8N3QV01_I2C		{5, 6, 7, 8}
+#define CONFIG_SYS_CH7301_I2C			{5, 6, 7, 8}
+#define CONFIG_SYS_ADV7611_I2C			{5, 6, 7, 8}
+#define CONFIG_SYS_DP501_I2C			{1, 2, 3, 4}
+#define CONFIG_STRIDER_FANS			{ {10, 0x4c}, {11, 0x4c}, \
+						  {12, 0x4c} }
+#else
+#define CONFIG_SYS_CH7301_I2C			{1, 2, 3, 4}
+#define CONFIG_SYS_ADV7611_I2C			{1, 2, 3, 4}
+#define CONFIG_SYS_DP501_I2C			{1, 2, 3, 4}
+#define CONFIG_STRIDER_FANS			{ {2, 0x18}, {3, 0x18}, \
+						  {4, 0x18} }
+#endif
+
+#ifndef __ASSEMBLY__
+void fpga_gpio_set(unsigned int bus, int pin);
+void fpga_gpio_clear(unsigned int bus, int pin);
+int fpga_gpio_get(unsigned int bus, int pin);
+#endif
+
+#ifdef CONFIG_STRIDER_CON
+#define I2C_SDA_GPIO	((I2C_ADAP_HWNR > 3) ? 0x0200 : 0x0040)
+#define I2C_SCL_GPIO	((I2C_ADAP_HWNR > 3) ? 0x0100 : 0x0020)
+#define I2C_FPGA_IDX	((I2C_ADAP_HWNR > 3) ? \
+			 (I2C_ADAP_HWNR - 4) : I2C_ADAP_HWNR)
+#else
+#define I2C_SDA_GPIO	0x0040
+#define I2C_SCL_GPIO	0x0020
+#define I2C_FPGA_IDX	I2C_ADAP_HWNR
+#endif
+#define I2C_ACTIVE	{ }
+#define I2C_TRISTATE	{ }
+#define I2C_READ \
+	(fpga_gpio_get(I2C_FPGA_IDX, I2C_SDA_GPIO) ? 1 : 0)
+#define I2C_SDA(bit) \
+	do { \
+		if (bit) \
+			fpga_gpio_set(I2C_FPGA_IDX, I2C_SDA_GPIO); \
+		else \
+			fpga_gpio_clear(I2C_FPGA_IDX, I2C_SDA_GPIO); \
+	} while (0)
+#define I2C_SCL(bit) \
+	do { \
+		if (bit) \
+			fpga_gpio_set(I2C_FPGA_IDX, I2C_SCL_GPIO); \
+		else \
+			fpga_gpio_clear(I2C_FPGA_IDX, I2C_SCL_GPIO); \
+	} while (0)
+#define I2C_DELAY	udelay(25)	/* 1/4 I2C clock duration */
+
+/*
+ * Software (bit-bang) MII driver configuration
+ */
+#define CONFIG_BITBANGMII		/* bit-bang MII PHY management */
+#define CONFIG_BITBANGMII_MULTI
+
+/*
+ * OSD Setup
+ */
+#define CONFIG_SYS_OSD_SCREENS		1
+#define CONFIG_SYS_DP501_DIFFERENTIAL
+#define CONFIG_SYS_DP501_VCAPCTRL0	0x01 /* DDR mode 0, DE for H/VSYNC */
+
+/*
+ * General PCI
+ * Addresses are mapped 1-1.
+ */
+#define CONFIG_SYS_PCIE1_BASE		0xA0000000
+#define CONFIG_SYS_PCIE1_MEM_BASE	0xA0000000
+#define CONFIG_SYS_PCIE1_MEM_PHYS	0xA0000000
+#define CONFIG_SYS_PCIE1_MEM_SIZE	0x10000000
+#define CONFIG_SYS_PCIE1_CFG_BASE	0xB0000000
+#define CONFIG_SYS_PCIE1_CFG_SIZE	0x01000000
+#define CONFIG_SYS_PCIE1_IO_BASE	0x00000000
+#define CONFIG_SYS_PCIE1_IO_PHYS	0xB1000000
+#define CONFIG_SYS_PCIE1_IO_SIZE	0x00800000
+
+/* enable PCIE clock */
+#define CONFIG_SYS_SCCR_PCIEXP1CM	1
+
+#define CONFIG_PCI
+#define CONFIG_PCI_INDIRECT_BRIDGE
+#define CONFIG_PCIE
+
+#define CONFIG_PCI_PNP		/* do pci plug-and-play */
+
+#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957	/* Freescale */
+#define CONFIG_83XX_GENERIC_PCIE_REGISTER_HOSES 1
+
+/*
+ * TSEC
+ */
+#define CONFIG_TSEC_ENET	/* TSEC ethernet support */
+#define CONFIG_SYS_TSEC1_OFFSET	0x24000
+#define CONFIG_SYS_TSEC1	(CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET)
+
+/*
+ * TSEC ethernet configuration
+ */
+#define CONFIG_MII		1 /* MII PHY management */
+#define CONFIG_TSEC1
+#define CONFIG_TSEC1_NAME	"eTSEC0"
+#define TSEC1_PHY_ADDR		1
+#define TSEC1_PHYIDX		0
+#define TSEC1_FLAGS		0
+
+/* Options are: eTSEC[0-1] */
+#define CONFIG_ETHPRIME		"eTSEC0"
+
+/*
+ * Environment
+ */
+#if 1
+#define CONFIG_ENV_IS_IN_FLASH	1
+#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE + \
+				 CONFIG_SYS_MONITOR_LEN)
+#define CONFIG_ENV_SECT_SIZE	0x10000 /* 64K(one sector) for env */
+#define CONFIG_ENV_SIZE		0x2000
+#define CONFIG_ENV_ADDR_REDUND	(CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE_REDUND	CONFIG_ENV_SIZE
+#else
+#define CONFIG_ENV_IS_NOWHERE
+#define CONFIG_ENV_SIZE		0x2000		/* 8KB */
+#endif
+
+#define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
+
+/*
+ * Command line configuration.
+ */
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_PING
+
+#define CONFIG_CMDLINE_EDITING	1	/* add command line history */
+#define CONFIG_AUTO_COMPLETE		/* add autocompletion support */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP		/* undef to save memory */
+#define CONFIG_SYS_LOAD_ADDR		0x2000000 /* default load address */
+#define CONFIG_SYS_HZ		1000	/* decrementer freq: 1ms ticks */
+
+#undef CONFIG_ZERO_BOOTDELAY_CHECK	/* ignore keypress on bootdelay==0 */
+
+#define CONFIG_SYS_CBSIZE	1024 /* Console I/O Buffer Size */
+
+#define CONFIG_SYS_CONSOLE_INFO_QUIET
+
+/* Print Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_MAXARGS	16	/* max number of command args */
+#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 256 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ	(256 << 20) /* Initial Memory map for Linux */
+
+/*
+ * Core HID Setup
+ */
+#define CONFIG_SYS_HID0_INIT	0x000000000
+#define CONFIG_SYS_HID0_FINAL	(HID0_ENABLE_MACHINE_CHECK | \
+				 HID0_ENABLE_INSTRUCTION_CACHE | \
+				 HID0_ENABLE_DYNAMIC_POWER_MANAGMENT)
+#define CONFIG_SYS_HID2		HID2_HBE
+
+/*
+ * MMU Setup
+ */
+
+/* DDR: cache cacheable */
+#define CONFIG_SYS_IBAT0L	(CONFIG_SYS_SDRAM_BASE | BATL_PP_RW | \
+					BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT0U	(CONFIG_SYS_SDRAM_BASE | BATU_BL_128M | \
+					BATU_VS | BATU_VP)
+#define CONFIG_SYS_DBAT0L	CONFIG_SYS_IBAT0L
+#define CONFIG_SYS_DBAT0U	CONFIG_SYS_IBAT0U
+
+/* IMMRBAR, PCI IO and FPGA: cache-inhibit and guarded */
+#define CONFIG_SYS_IBAT1L	(CONFIG_SYS_IMMR | BATL_PP_RW | \
+			BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_IBAT1U	(CONFIG_SYS_IMMR | BATU_BL_8M | BATU_VS | \
+					BATU_VP)
+#define CONFIG_SYS_DBAT1L	CONFIG_SYS_IBAT1L
+#define CONFIG_SYS_DBAT1U	CONFIG_SYS_IBAT1U
+
+/* FLASH: icache cacheable, but dcache-inhibit and guarded */
+#define CONFIG_SYS_IBAT2L	(CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \
+					BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT2U	(CONFIG_SYS_FLASH_BASE | BATU_BL_8M | \
+					BATU_VS | BATU_VP)
+#define CONFIG_SYS_DBAT2L	(CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \
+					BATL_CACHEINHIBIT | \
+					BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_DBAT2U	CONFIG_SYS_IBAT2U
+
+/* Stack in dcache: cacheable, no memory coherence */
+#define CONFIG_SYS_IBAT3L	(CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW)
+#define CONFIG_SYS_IBAT3U	(CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | \
+					BATU_VS | BATU_VP)
+#define CONFIG_SYS_DBAT3L	CONFIG_SYS_IBAT3L
+#define CONFIG_SYS_DBAT3U	CONFIG_SYS_IBAT3U
+
+/*
+ * Environment Configuration
+ */
+
+#define CONFIG_ENV_OVERWRITE
+
+#if defined(CONFIG_TSEC_ENET)
+#define CONFIG_HAS_ETH0
+#endif
+
+#define CONFIG_BAUDRATE 115200
+
+#define CONFIG_LOADADDR	800000	/* default location for tftp and bootm */
+
+#define CONFIG_BOOTDELAY	5	/* -1 disables auto-boot */
+
+#define CONFIG_HOSTNAME		hrcon
+#define CONFIG_ROOTPATH		"/opt/nfsroot"
+#define CONFIG_BOOTFILE		"uImage"
+
+#define CONFIG_PREBOOT		/* enable preboot variable */
+
+#define	CONFIG_EXTRA_ENV_SETTINGS					\
+	"netdev=eth0\0"							\
+	"consoledev=ttyS1\0"						\
+	"u-boot=u-boot.bin\0"						\
+	"kernel_addr=1000000\0"					\
+	"fdt_addr=C00000\0"						\
+	"fdtfile=hrcon.dtb\0"				\
+	"load=tftp ${loadaddr} ${u-boot}\0"				\
+	"update=protect off " __stringify(CONFIG_SYS_MONITOR_BASE)	\
+		" +${filesize};era " __stringify(CONFIG_SYS_MONITOR_BASE)\
+		" +${filesize};cp.b ${fileaddr} "			\
+		__stringify(CONFIG_SYS_MONITOR_BASE) " ${filesize}\0"	\
+	"upd=run load update\0"						\
+
+#define CONFIG_NFSBOOTCOMMAND						\
+	"setenv bootargs root=/dev/nfs rw "				\
+	"nfsroot=$serverip:$rootpath "					\
+	"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
+	"console=$consoledev,$baudrate $othbootargs;"			\
+	"tftp ${kernel_addr} $bootfile;"				\
+	"tftp ${fdt_addr} $fdtfile;"					\
+	"bootm ${kernel_addr} - ${fdt_addr}"
+
+#define CONFIG_MMCBOOTCOMMAND						\
+	"setenv bootargs root=/dev/mmcblk0p3 rw rootwait "		\
+	"console=$consoledev,$baudrate $othbootargs;"			\
+	"ext2load mmc 0:2 ${kernel_addr} $bootfile;"			\
+	"ext2load mmc 0:2 ${fdt_addr} $fdtfile;"			\
+	"bootm ${kernel_addr} - ${fdt_addr}"
+
+#define CONFIG_BOOTCOMMAND		CONFIG_MMCBOOTCOMMAND
+
+
+#endif	/* __CONFIG_H */
diff --git a/include/gdsys_fpga.h b/include/gdsys_fpga.h
index f8d8322..69d248f 100644
--- a/include/gdsys_fpga.h
+++ b/include/gdsys_fpga.h
@@ -197,6 +197,69 @@
 };
 #endif
 
+#ifdef CONFIG_STRIDER_CPU
+struct ihs_fpga {
+	u16 reflection_low;	/* 0x0000 */
+	u16 versions;		/* 0x0002 */
+	u16 fpga_version;	/* 0x0004 */
+	u16 fpga_features;	/* 0x0006 */
+	u16 reserved_0[1];	/* 0x0008 */
+	u16 top_interrupt;	/* 0x000a */
+	u16 reserved_1[3];	/* 0x000c */
+	u16 extended_control;	/* 0x0012 */
+	struct ihs_gpio gpio;	/* 0x0014 */
+	u16 mpc3w_control;	/* 0x001a */
+	u16 reserved_2[2];	/* 0x001c */
+	struct ihs_io_ep ep;	/* 0x0020 */
+	u16 reserved_3[9];	/* 0x002e */
+	u16 mc_int;		/* 0x0040 */
+	u16 mc_int_en;		/* 0x0042 */
+	u16 mc_status;		/* 0x0044 */
+	u16 mc_control;		/* 0x0046 */
+	u16 mc_tx_data;		/* 0x0048 */
+	u16 mc_tx_address;	/* 0x004a */
+	u16 mc_tx_cmd;		/* 0x004c */
+	u16 mc_res;		/* 0x004e */
+	u16 mc_rx_cmd_status;	/* 0x0050 */
+	u16 mc_rx_data;		/* 0x0052 */
+	u16 reserved_4[62];	/* 0x0054 */
+	struct ihs_i2c i2c0;	/* 0x00d0 */
+};
+#endif
+
+#ifdef CONFIG_STRIDER_CON
+struct ihs_fpga {
+	u16 reflection_low;	/* 0x0000 */
+	u16 versions;		/* 0x0002 */
+	u16 fpga_version;	/* 0x0004 */
+	u16 fpga_features;	/* 0x0006 */
+	u16 reserved_0[1];	/* 0x0008 */
+	u16 top_interrupt;	/* 0x000a */
+	u16 reserved_1[4];	/* 0x000c */
+	struct ihs_gpio gpio;	/* 0x0014 */
+	u16 mpc3w_control;	/* 0x001a */
+	u16 reserved_2[2];	/* 0x001c */
+	struct ihs_io_ep ep;	/* 0x0020 */
+	u16 reserved_3[9];	/* 0x002e */
+	struct ihs_i2c i2c0;	/* 0x0040 */
+	u16 reserved_4[10];	/* 0x004c */
+	u16 mc_int;		/* 0x0060 */
+	u16 mc_int_en;		/* 0x0062 */
+	u16 mc_status;		/* 0x0064 */
+	u16 mc_control;		/* 0x0066 */
+	u16 mc_tx_data;		/* 0x0068 */
+	u16 mc_tx_address;	/* 0x006a */
+	u16 mc_tx_cmd;		/* 0x006c */
+	u16 mc_res;		/* 0x006e */
+	u16 mc_rx_cmd_status;	/* 0x0070 */
+	u16 mc_rx_data;		/* 0x0072 */
+	u16 reserved_5[70];	/* 0x0074 */
+	struct ihs_osd osd;	/* 0x0100 */
+	u16 reserved_6[889];	/* 0x010e */
+	u16 videomem[31736];	/* 0x0800 */
+};
+#endif
+
 #ifdef CONFIG_DLVISION_10G
 struct ihs_fpga {
 	u16 reflection_low;	/* 0x0000 */